245/45R19vs325/30R20
Proportional side-by-side visual comparison, dimensional specs, speedometer calibration, and fitment guide.
Comparison Summary & Verdict
Comparing 245/45R19 (baseline) to 325/30R20 (target):The 325/30R20 is 0.00" shorter in overall diameter (0%) and 3.15" wider.
Side-by-Side Dimension Specifications
Full dimensional metrics calculated according to ISO standardized tire formulas.
| Specification | 245/45R19 (Stock) | 325/30R20 (Target) | Difference (Delta) |
|---|---|---|---|
| Overall Diameter | 27.68" (703 mm) | 27.68" (703 mm) | 0.00" (0%) |
| Section Width | 9.65" (245 mm) | 12.8" (325 mm) | +3.15" (+80 mm) |
| Sidewall Height | 4.34" (110 mm) | 3.84" (98 mm) | -0.50" |
| Circumference | 86.96" (2209 mm) | 86.95" (2209 mm) | -0.01" |
| Revolutions per Mile | 751 revs/mi | 751 revs/mi | 0 revs/mi |
| Wheel Rim Diameter | 19" | 20" | +1" (Requires different wheels) |
| Recommended Rim Width | 6.6" – 8.6" | 8.8" – 11.4" | n/a |
Speedometer & Odometer Calibration Table
Because vehicle speedometers measure axle rotation, changing tire circumference alters speed readings. When switching from 245/45R19 to 325/30R20:
| Actual Speed (GPS) | Speedometer Reading on 325/30R20 | Variance / Error |
|---|---|---|
| 20 mph | 20.0 mph | +0.0 mph |
| 30 mph | 30.0 mph | +0.0 mph |
| 45 mph | 45.0 mph | +0.0 mph |
| 60 mph | 60.0 mph | +0.0 mph |
| 70 mph | 70.0 mph | +0.0 mph |
| 80 mph | 80.0 mph | +0.0 mph |
Fitment & Practical Considerations
Clearance & Rubbing
Because 325/30R20 is significantly different in size (0.00" shorter), check clearance with suspension components, brake calipers, and wheel wells at full steering lock and full compression.
Gearing & Acceleration
Gearing and acceleration changes will be negligible between these two sizes.
Wheel & Rim Width
Note: 245/45R19 requires a 19" wheel, while 325/30R20 requires a 20" wheel. You must purchase new wheels to make this swap.
The 3% Rule: What 0% Actually Means
Every badge on this page measures 245/45R19 against 325/30R20 using the same industry convention: a replacement tire should stay within3% of the original overall diameter. These two sizes differ by0%, which is inside that band.
Where the number comes from
A speedometer does not measure road speed. It counts how fast the drivetrain turns and multiplies by an assumed tire circumference, set at the factory for the original size. Fit a tire with a different circumference and every reading derived from that assumption shifts by the same proportion: speed, odometer distance, and the wheel-speed inputs that ABS, traction control and automatic shift points work from. 3% is the tolerance the industry settles on as small enough for those systems to keep behaving as calibrated.
What it measures, and what it does not
The rule is about diameter alone. It says nothing about section width, so two sizes can sit comfortably inside 3% and still differ enough in width to contact suspension components or fender liners. It also says nothing about load rating. Treat a pass as one box ticked, not as clearance to fit.
How it applies here
At 0%, 325/30R20 keeps speedometer error small: at an actual 60 mph the dial reads 60 mph. Odometer distance shifts by the same proportion. Note that these sizes use different wheel diameters (19" and 20"), so this swap means new wheels as well as new tires.
One caveat specific to this site: the revolutions per mile above are corrected for the loaded rolling radius of a tire, which is smaller than the free diameter because the contact patch flattens. The 3% comparison itself is a ratio of two circumferences, so that correction cancels out and does not affect it.
Official Calculation Standards & References
All dimension formulas, revs/mile conversions, rim width brackets, and speedometer error deltas on Tire Visualizer are calculated strictly according to international automotive engineering standards:
ISO 4000-1 metric tire dimensional standards, section width ratios, and approved measuring rim definitions.
North American standards for overall tire diameter, static loaded radius, and revolutions-per-mile benchmarks.
Federal motor vehicle safety standards governing pneumatic tire sizing, load indices, and speedometer tolerance limits.
Engineering standards (SAE J2047 & J1982) for dynamic tire rolling radius and speedometer calibration accuracy.
Frequently Asked Questions: 245/45R19 vs 325/30R20
Can I replace 245/45R19 with 325/30R20?
Yes. The diameter difference between 245/45R19 and 325/30R20 is 0%, which is within the industry standard ±3% safety margin. It is generally a safe direct replacement without requiring speedometer recalibration or suspension modifications.
How does 325/30R20 affect my speedometer compared to 245/45R19?
When driving at an actual speed of 60 mph on 325/30R20, your speedometer will read 60 mph (a difference of 0.0 mph). Your vehicle will be traveling slightly slower than indicated.
Will 325/30R20 change my vehicle's ride height?
325/30R20 has an overall diameter of 27.68" compared to 27.68" on 245/45R19. This will change your ground clearance by 0.00 inches (lower).
What wheel rim width is needed for 325/30R20?
For 325/30R20, the recommended wheel rim width range is typically 8.8" to 11.4" wide, mounted on a 20" diameter wheel.
What is the 3% rule for tires?
The 3% rule is the industry convention that a replacement tire should stay within 3% of the original overall diameter. Inside that band, speedometer and odometer error stays small enough that ABS, traction control and transmission shift points keep working from readings they were calibrated against. Between 245/45R19 and 325/30R20 the diameter difference is 0%, which is inside the 3% band.
Compare Other Tire Sizes
Select any two tire sizes to generate an instant visual diagram.