255/70R18vs255/75R17
Proportional side-by-side visual comparison, dimensional specs, speedometer calibration, and fitment guide.
Comparison Summary & Verdict
Comparing 255/70R18 (baseline) to 255/75R17 (target):The 255/75R17 is 0.00" shorter in overall diameter (0%) and 0.00" wider.
Side-by-Side Dimension Specifications
Full dimensional metrics calculated according to ISO standardized tire formulas.
| Specification | 255/70R18 (Stock) | 255/75R17 (Target) | Difference (Delta) |
|---|---|---|---|
| Overall Diameter | 32.06" (814 mm) | 32.06" (814 mm) | 0.00" (0%) |
| Section Width | 10.04" (255 mm) | 10.04" (255 mm) | 0.00" (+0 mm) |
| Sidewall Height | 7.03" (179 mm) | 7.53" (191 mm) | +0.50" |
| Circumference | 100.7" (2558 mm) | 100.72" (2558 mm) | +0.02" |
| Revolutions per Mile | 649 revs/mi | 649 revs/mi | 0 revs/mi |
| Wheel Rim Diameter | 18" | 17" | -1" (Requires different wheels) |
| Recommended Rim Width | 6.9" – 8.9" | 6.9" – 8.9" | n/a |
Speedometer & Odometer Calibration Table
Because vehicle speedometers measure axle rotation, changing tire circumference alters speed readings. When switching from 255/70R18 to 255/75R17:
| Actual Speed (GPS) | Speedometer Reading on 255/75R17 | Variance / Error |
|---|---|---|
| 20 mph | 20.0 mph | -0.0 mph |
| 30 mph | 30.0 mph | -0.0 mph |
| 45 mph | 45.0 mph | -0.0 mph |
| 60 mph | 60.0 mph | -0.0 mph |
| 70 mph | 70.0 mph | -0.0 mph |
| 80 mph | 80.0 mph | -0.0 mph |
Fitment & Practical Considerations
Clearance & Rubbing
Because 255/75R17 has very similar dimensions to 255/70R18 (only 0.00" diameter difference), clearance issues or fender rubbing are extremely unlikely on stock suspension.
Gearing & Acceleration
Gearing and acceleration changes will be negligible between these two sizes.
Wheel & Rim Width
Note: 255/70R18 requires a 18" wheel, while 255/75R17 requires a 17" wheel. You must purchase new wheels to make this swap.
The 3% Rule: What 0% Actually Means
Every badge on this page measures 255/70R18 against 255/75R17 using the same industry convention: a replacement tire should stay within3% of the original overall diameter. These two sizes differ by0%, which is inside that band.
Where the number comes from
A speedometer does not measure road speed. It counts how fast the drivetrain turns and multiplies by an assumed tire circumference, set at the factory for the original size. Fit a tire with a different circumference and every reading derived from that assumption shifts by the same proportion: speed, odometer distance, and the wheel-speed inputs that ABS, traction control and automatic shift points work from. 3% is the tolerance the industry settles on as small enough for those systems to keep behaving as calibrated.
What it measures, and what it does not
The rule is about diameter alone. It says nothing about section width, so two sizes can sit comfortably inside 3% and still differ enough in width to contact suspension components or fender liners. It also says nothing about load rating. Treat a pass as one box ticked, not as clearance to fit.
How it applies here
At 0%, 255/75R17 keeps speedometer error small: at an actual 60 mph the dial reads 60 mph. Odometer distance shifts by the same proportion. Note that these sizes use different wheel diameters (18" and 17"), so this swap means new wheels as well as new tires.
One caveat specific to this site: the revolutions per mile above are corrected for the loaded rolling radius of a tire, which is smaller than the free diameter because the contact patch flattens. The 3% comparison itself is a ratio of two circumferences, so that correction cancels out and does not affect it.
Official Calculation Standards & References
All dimension formulas, revs/mile conversions, rim width brackets, and speedometer error deltas on Tire Visualizer are calculated strictly according to international automotive engineering standards:
ISO 4000-1 metric tire dimensional standards, section width ratios, and approved measuring rim definitions.
North American standards for overall tire diameter, static loaded radius, and revolutions-per-mile benchmarks.
Federal motor vehicle safety standards governing pneumatic tire sizing, load indices, and speedometer tolerance limits.
Engineering standards (SAE J2047 & J1982) for dynamic tire rolling radius and speedometer calibration accuracy.
Frequently Asked Questions: 255/70R18 vs 255/75R17
Can I replace 255/70R18 with 255/75R17?
Yes. The diameter difference between 255/70R18 and 255/75R17 is 0%, which is within the industry standard ±3% safety margin. It is generally a safe direct replacement without requiring speedometer recalibration or suspension modifications.
How does 255/75R17 affect my speedometer compared to 255/70R18?
When driving at an actual speed of 60 mph on 255/75R17, your speedometer will read 60 mph (a difference of 0.0 mph). Your vehicle will be traveling slightly slower than indicated.
Will 255/75R17 change my vehicle's ride height?
255/75R17 has an overall diameter of 32.06" compared to 32.06" on 255/70R18. This will change your ground clearance by 0.00 inches (lower).
What wheel rim width is needed for 255/75R17?
For 255/75R17, the recommended wheel rim width range is typically 6.9" to 8.9" wide, mounted on a 17" diameter wheel.
What is the 3% rule for tires?
The 3% rule is the industry convention that a replacement tire should stay within 3% of the original overall diameter. Inside that band, speedometer and odometer error stays small enough that ABS, traction control and transmission shift points keep working from readings they were calibrated against. Between 255/70R18 and 255/75R17 the diameter difference is 0%, which is inside the 3% band.
Compare Other Tire Sizes
Select any two tire sizes to generate an instant visual diagram.